Fluid Film Gel BN & BW
- IMPA 40000009
- Contact Us
Fluid Film Gel BN
菲路特万能凝胶保养剂
FLUID FILM GEL BW (white) &
GEL BN (natural)
Product Data: #202
Effective October 2013
Permanently soft gel coating for all metals. Will not evaporate. Lanolin-based coating. Solvent free. Non-toxic.
Anti-corrosive coating for all metals. Protects against attack by moisture, salt solutions and atmospheres in marine, agriculture and industrial environments.
Applications are made in a single coat to ballast tanks, void spaces, pontoons, etc., on both new and old constructions. For use on equipment requiring protection from corrosion for extended periods.
Not recommended for extended exposure to bright sunlight. For these applications use FLUID FILM GEL BEW (Exterior). See Technical Bulletin #202.3.
If conditions dictate a heavier or lighter coating or lubricant, refer to other EUREKA CHEMICAL product bulletins for semi-liquids, gels and greases or consult EUREKA CHEMICAL COMPANY.
Application for Heavy Marine | ||
Surface Preparation: |
|
New Construction: No sandblasting required. Remove any loose mill scale. Welding flux residues must be removed by wire brushing followed by washing with clean water. Clean up all debris. If surface has been shop primed with inorganic zinc, do not coat until the zinc has been cured a minimum of 30 days. In Service Equipment: No sandblasting required. Remove flaking rust and peeling paint. Break all blisters larger than |
Number of Coats: |
|
1 |
Typical Coverage Per Drum: |
|
On very heavy rust, visual inspection is required for best thickness recommendation. |
Thinning: |
|
Do not thin. |
Curing Time: |
|
None. Equipment may be used immediately after coating. |
Methods: |
|
Airless spray, roller, brush. |
Heating Required: |
|
Under extreme cold conditions, storage of material in a warm room will facilitate application. |
Spray Equipment: |
|
Alemite 7896 pump (22/1 ratio) or equal, and a flow gun. See Technical Bulletin #202.1. |
Clean Up: |
|
Scrape off excess then wash with hot water and mild detergent or any commercial degreaser. |
Protective Equipment: |
|
When spraying use approved eye protection to safeguard against potential eye contact. Use respirator or gas mask with appropriate cartridges and canisters (NIOSH approved, if available) to remove oil mist. If making repairs by brush, a respirator is not required. |
Typical Properties | ||
(ASTM-D1535)Specific Gravity: Specific Gravity: |
|
0.915 - 0.925 |
Color: |
|
White: 2.5YO / 2 or lighter. |
Flash Point: |
|
|
Unworked Penetration: |
|
200-230 ( |
Specific Conductivity: |
|
Less than 10-9 mho/cm @
|
VOC: |
|
1.71%
|
Effect on Rubber: |
|
None on neoprene and buna-n. May cause swelling on non oil-resistant rubber goods. |
Effect on Paint: |
|
None on most painted surfaces. |
Effect on Aluminum: |
|
No pitting. |
Effect on Copper, Brass: |
|
No staining. |
Effect on Steel: |
|
No hydrogen embrittlement. |
Dropping Point: |
|
96C (205F). This value is given for information purposes only and is not to be construed as a recommendation for maximum temperature use. |
Toxicity: |
|
Oral: LD 50 greater than 16ml / kilogram (relatively harmless). Skin Irritation: Score 0.83 (minimal irritation). Title 16 CFR Section 1500.41. Eye Irritation: Negative. Title 16 CFR Section 1500.42. |
Performance: |
|
Salt Fog (Inches/Year): Simulated Ballast Tank: |
Note 1: When welding in tanks coated with FLUID FILM, wipe material back a distance of 1.5 meters (5 feet) from where hot work is to be performed and from the deck area beneath the hot work. See Technical Bulletin #202.2.
Note 2: If FLUID FILM is applied over metal covered with scale, even though tightly adhering, anodes must not be present. If the anodes are not to be removed, then the surface must be cleaned to conform to Steel Structures Painting Council SSPC-SP3.
Note 3: Maximum usable temperature is 65C (150F). Ballast tanks should be filled with water 4 to 5 days before hot cargo taken on in those cargo tanks that are adjacent to ballast tanks.
All components of FLUID FILM® GEL BW & BN are listed on the TSCA Inventory.
KEEP OUT OF REACH OF CHILDREN.